Note: Your comments/feedback should be limited to this FAQ only. Send "nvram set STARTUP=\"boot -z -elf flash1.os:\"" The configuration will be saved to file so that it can be reused to connect to the same device again in the future, which is convenient. This post documents how to configure Minicom for establishing an interactive terminal session with a device connected to your computer via a serial port. Send "nvram set et0config=\"192.168.100.102 255.255.255.0 192.168.100.1\"" Introduction I recently wrote about my first experience connecting to the pinephone via serial console. picocom is a tiny dumb-terminal emulation program that is very like minicom, but instead of mini, it is pico. To end the session, press Ctrl+A followed by Ctrl+X. Send "nvram set et2macaddr=00-30-48-98-C3-D9" Restart minicom with the serial cable connected to the target machine. Make sure enter the command ânvram commitâ at the end, before âresetâ (restart) the switch. If no Linux minicom is used, please issue the commands between the quotation marks manually, one by one. Please edit the script and change the MAC address to the unitâs MAC address. The script file is to run under Linux minicom terminal emulator. Itâs very easy to interface it with other devices. The Raspberry Pi is a very inexpensive, and even in 2023, relatively available embedded board. Please copy & paste the script below to a text file. The modern Mac platform makes a great development environment for embedded programming. If the ânvram showâ command in console returns the â*** command status = 0â result, the configuration in the NVRAM is gone. press 'B' and change location to the directory you have write permission. sudo minicom -s .You can change the lockfile location as follow, 1. So, we did a reset on the blade âGigabit Switch Statusâ web administration page.Ĭonnecting through the rs232 port, we configured IP address for the switch and got the following output:ĬFE> ifconfig eth0 -addr=10.4.17.151 -mask=255.255.255.0 -gw=10.4.17.254Äevice eth0: hwaddr 00-30-48-58-36-10, ipaddr 10.4.17.151, mask 255.255.255.0 The default place for lock file is /opt/local/var, where unprivileged user is not permitted to write. The BMB-GEM-003 switch stopped responding on the web management interface. All opinions are my own.FAQ Entry | Online Support | Support - Super Micro Computer, Inc. My research involves embedded systems, operating systems, trusted and confidential computing, and hardware security and trust. I am Dave Jing Tian, an Assistant Professor in the Department of Computer Science at Purdue University working on system security. Conexión del entorno: Utilice un cable serial de agujero a agujero para conectar la placa al sistema Linux Paso 3. Preparación del sistema Linux: Instale un sistema Linux, como centos 7 (la PC de este sistema debe admitir puertos serie) Paso 2. Texas Instruments X-Loader 1.5.1 (â 08:47:49) Requisito previo: la herramienta minicom se ha instalado en el sistema Linux. Run the command above and then power on the gumstix and then login~ Hunting under /dev, you will find it â tty.usbserial-A7005snv. In my case, I am using a USB converter and the gumstix is eventually connected to my Mac via a USB port. You have to figure out the name of the device after the gumstix is connected. The link from is still helpful for all these configurations except for the name of the device. First, we need to choose âSerial Port Setupâ and then configure the device and the connection. This will drive you into the interactive menu of minicom. NOTE: brew update may be needed or the latest version of Xcode (command line tools) is needed for the latest Mac OS (10.9) So please install either brew or port as your apt-get/yum for the Mac. Of course, we do not want to bootstrap from the source file. We will try to install minicom into Mac OS. Minicom is always recommended based on the previous experience. Now you can get connected to Maximite via a terminal program (for example, minicom, which can be installed via Homebrew as brew install minicom in the terminal). This post will show a real example for Mac OS (10.9) to connect with a gumstix (Overo+Palo35) using minicom. has provided the most useful information for developers about gumstix development, though a little bit out dated.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |